DUCK PICTURES!!!!!LET'S SEE 'EM!! OOSers, YOU TOO!!

Discussion in 'Arkansas Flyway Forum' started by MGDUCK2, Jan 28, 2013.

  1. eriecutemoutfitter

    eriecutemoutfitter Senior Refuge Member

    Messages:
    879
    Joined:
    Feb 26, 2010
    Location:
    Puyallup
    I wish that were possible but I can't........ I'm deployed. :rolleyes:
     
  2. da fowl slayer

    da fowl slayer Elite Refuge Member

    Messages:
    2,299
    Joined:
    Aug 14, 2000
    Location:
    TN
    Erie
    Thanks for your service brother. Pm your name and address and colors and I will make sure you have a little something waiting for your safe return.
    Thx again brother!
     
  3. MGDUCK2

    MGDUCK2 Elite Refuge Member

    Messages:
    18,248
    Joined:
    Nov 21, 2002
    Location:
    Bayou Meto, Ark (By-uh-Meeta)
    Great Pictures!!

    Ain't no Rookie behind that camera....
     
  4. stumpy waters

    stumpy waters Elite Refuge Member

    Messages:
    3,709
    Joined:
    Jun 14, 2002
    Location:
    Arkansas
    Hey Ghost Duck,

    That pic with the Heiman pose, is that a piece of PVC extending that suzuki tiller??

    Seriously just wondering if you bought that or made it, been wanting to lengthen mine just haven't come up with anything bought or made I trust yet.
     
  5. hhpage

    hhpage Senior Refuge Member

    Messages:
    593
    Joined:
    Jan 11, 2005
    Location:
    Arkansas
    I've been running a PVC tiller extension for the past ten years. Used the same design on two different 25 hp motors with absolutely zero issues. I use gray PVC conduit (2"?; whatever size will just not quite slide easily onto the tiller handle) and a rubber pipe fitting with two hose clamps. Cut three grooves lengthwise on the tiller end of the PVC. The grooves should be about 2/3 the length of the tiller grip. This provides enough flex to get the PVC over the tiller grip. Put the rubber coupler onto the tiller grip, then slide the PVC onto the grip inside of the rubber coupler. Tighten both hose clamps and you're good to go. I also wrap the grip end of the PVC with closed cell foam and cloth tape to provide a better grip surface. I can run my motor standing up or sitting down with this setup, just make sure you allow enough room to get out of the way of the tiller handle when you pull it hard to the driver's side. :tu
     
  6. MGDUCK2

    MGDUCK2 Elite Refuge Member

    Messages:
    18,248
    Joined:
    Nov 21, 2002
    Location:
    Bayou Meto, Ark (By-uh-Meeta)
    Mountain Feist Duck Dog.....20#s.....:h

    [​IMG]
     
  7. getemshug

    getemshug Senior Refuge Member

    Messages:
    514
    Joined:
    Nov 17, 2008
    Location:
    Arkansas

    Good looking dog. I guess he'll tree every now and then.:yes

    My dad recently got two Mullins fiests. Hope they'll tree some this next weekend....
     
  8. ghost duck

    ghost duck Senior Refuge Member

    Messages:
    159
    Joined:
    Aug 26, 2008
    Location:
    Arkansas


    what he said only i believe i used 3 hose clamps. ran the cmc t&t switch out the end as well
     
  9. eriecutemoutfitter

    eriecutemoutfitter Senior Refuge Member

    Messages:
    879
    Joined:
    Feb 26, 2010
    Location:
    Puyallup
    Not sure if this thread is for Arkansas only but I'll share a few of my favorite pictures from this year.

    Started in Canada in October and it was everything I grew up dreaming about.
    [​IMG]

    [​IMG]

    This was my camp for a week.
    [​IMG]

    [​IMG]

    [​IMG]
     
  10. eriecutemoutfitter

    eriecutemoutfitter Senior Refuge Member

    Messages:
    879
    Joined:
    Feb 26, 2010
    Location:
    Puyallup
    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]

    Already planning for next year!
    [​IMG]
     

Share This Page