Search results

  1. Iammichael6499

    Most dangerous jobs you have had

    Being a son-in-law is much more dangerous.
  2. Iammichael6499

    New to TSS - equipment - 28 gauge

    My wife!
  3. Iammichael6499

    Strangest duck hunting setup you’ve tried

    I sat on the roof of my parent's house, near Tulsa, Oklahoma, and shot at passing geese. Unfortunately, there are no photos of my attempts. If tungsten had been available back then, I'm sure I would have been more successful.
  4. Iammichael6499

    Wood … Remington 1100 or 11-87 Stock and Forend

    Just a thought. You might be able to reduce the forearm indentions by "steaming" them. I did that successfully on an unfinished stock but never tried it on a finished one.
  5. Iammichael6499

    Wood … Remington 1100 or 11-87 Stock and Forend

    I found this set in my dad’s gun closet. It was in a display pack marked “Remington 1100/11-87 synthetic stock and forend”. Obviously it’s not. The forend has a few indentions on the bottom (see pic 5) and the stock “feels” like the grain is ever so slightly raised (see pic 4 of straight...
  6. Iammichael6499

    Are you looking for a shorter barrel Citori? Trade Excellent Browning Citori 20ga w/ 26" barrels for comparable Browning Citori 20ga w/ 28"barrels

    I knew it was a long shot, pun intended, but I'll leave this post and offer up for now.
  7. Iammichael6499

    Have you ever had a transmittable disease?

    Is waterfowl hunting considered a "transmittable disease"?
  8. Iammichael6499

    28 ga, TSS and Win AA HS Hulls

    Reviving a dated thread. I'm about to give up on loading 28 ga TSS/steel duplex any time soon. I've had no luck sourcing 28 ga Cheddite hulls or 28 ga TPS wads. All I've found so far are Cheddite primers, 28 gauge primed red Fiocchi hulls and "premium priced" Lilgun Powder. To date, I've had...
  9. Iammichael6499

    New PCP Rifle and Maintenance Challenges

    I finally lapped the Leupold medium height rings today and installed the Leupold VX-3 1.75-6x32. At low powers I’m seeing a little distortion from the barrel in the bottom of the scope sight-picture but I want to keep the scope as low as possible so I’ll live with it. Pics below show how the...
  10. Iammichael6499

    Rethinking our boat strategy

    It’s a pain if you are hunting alone to lift/slide the 12’ out of the 18’, put it in the truck, throw all the decoys/gear back in, pull it out, reattach the motor, etc. Why can’t you use the 18’ in the WMA?
  11. Iammichael6499

    New PCP Rifle and Maintenance Challenges

    Not sure what I was thinking at the time, but I ordered the wrong scope rings. The Marauder has an 11mm rail ... not a 3/8" so I sent the rings back to Amazon. I then dug around in my scope base/ring inventory to find a set of medium height 11mm Leupold rings (gloss). Upon mounting the rings...
  12. Iammichael6499

    Are you looking for a shorter barrel Citori? Trade Excellent Browning Citori 20ga w/ 26" barrels for comparable Browning Citori 20ga w/ 28"barrels

    Are you looking for a shorter barrel Citori? I'll trade my excellent (1994) Browning Citori Lightning Invector Plus 20ga w/ 26" barrels for a comparable Browning Citori 20ga w/ 28" barrels. If interested I'll post or send pics of said Citori.
  13. Iammichael6499

    MEC 650

    BUT, when it’s 100 degrees outside and the basement is 67 degrees I don’t mind taking 3 times as long to load a round even if it’s “overkill” in the precision category.
  14. Iammichael6499

    Back in OK.........

    I think I'm familiar with that location. If I'm correct it's just off the Arkansas River on a Keystone WMA.
  15. Iammichael6499

    New PCP Rifle and Maintenance Challenges

    The first pellets I ordered were JSB Match Diabolo’s (18.3 gr) scheduled to arrive today. My Leupold PRW 1” High Cross-Slot scope rings won’t get here until Monday or Tuesday. I wasn’t paying attention to how high the magazine protruded and hence thought low PRW’s I already had in hand would...
  16. Iammichael6499

    New PCP Rifle and Maintenance Challenges

    Good to know. I plan to do the TSS mod after I’ve shot it for awhile, settled on a pellet brand and created a Chronograph history.
  17. Iammichael6499

    MEC 650

    650's are nice loaders and auctions are an excellent way to get Mec loaders at a great price. I have four Sizemasters (12, 20, 28, 410) and two 600 Jr's. (12, 20) that I bought from auctions. I stopped shooting trap tournaments a long time ago so I really don't have a sound reason to have...
  18. Iammichael6499

    MEC 650

    What gauge?
  19. Iammichael6499

    Tru Lock chokes

    Ditto on the patterns. Patterns have been much better/consistent from my A400 Xtreme with Trulock chokes than with the Beretta OEM chokes.
  20. Iammichael6499

    So who’s scalping Raspberry Girl Scout Cookies?

    Have you checked with the Sinaloa Cartel yet?

Latest posts

Top